NU folosiți lipici... explic la sfârșitul recenziei. Acesta este un sfat prost pe care îl văd aruncat în jur.
Am scăzut 1 stea din cauza unei probleme pe care produsul o are la una dintre curelele de aliniere. Butonul de plastic pare să fi fost lovit. Nu am idee a cui este vina, dar scade precizia pe axa x chiar în mijlocul mașinii cu aproximativ 1 mm. Aceasta este o mică discrepanță, dar înseamnă că nu este perfect. Pentru prețul la care l-am găsit, totuși, redus cu aproximativ 40% mai ieftin, este un 5 din 5. Mă gândesc să cumpăr această piesă pentru a o instala din nou, deoarece chiar nu pot fi deranjat să returnez mașina, așteptând întreaga poveste pentru a o recupera.
Instalarea a fost destul de ușoară, ajustările pentru cât de strânse trebuie să fie șuruburile sunt foarte vagi în toate ghidurile.
A fost puțin consumatoare de timp pentru a o face să funcționeze, dar un proces distractiv. Așadar, cu siguranță nu a fost „funcționare din cutie” cum spun unii.
Totul celălalt este perfect și îmi place procesul.
Un mic sfat, toată lumea tot spune că modelul nu se lipsește de bază. Prin programul tău de tăiere, fie adaugă baza care îl va susține, adaugă aproximativ un gram în plus de imprimare, dar chiar mai bine, am descoperit că setând programul de tăiere să facă primul strat la +5 grade funcționează perfect. Imprimarea se lipește și nu se mișcă nici măcar când este terminată, trebuie să o lași să se răcească. E atât de bun. Așadar, pentru PLA, pui stratul 1 la 65 de grade, iar eu am imprimat un obiect de 2 cm x 3 cm cu înălțimea de 25 cm fără nicio problemă. Folosesc asta pentru toate testele curente și totul se lipește corect și nu se mișcă.
NU recomand utilizarea lipiciului. Cred că în cele din urmă va compromite calitatea. Și deoarece există o soluție mai bună, adăugarea de lucruri precum lipiciul este pur și simplu inutilă.
Până acum, totul este bine, în afară de acea problemă cu piesa care este îndoită. Totul celălalt este grozav.
Do NOT use glue... I explain at end of review. This is a bad tip I see thrown around.
i have taken off 1 star due to an issue the product has on one of the alignment belts. the plastic knob seems to have been hit. no idea whos fault this is, but it drops the accuracy on the x axis right down the middle of the machine at around 1mm. this is a small discrepancy, but means its not perfect. for the price i found this for however, discounted at around 40% cheaper its a 5 out of 5. i am looking into purchasing this part so I can install it again, as I really can't be bothered sending the machine back, waiting for the whole ordeal to get it back.
installation was rather easy, the adjustments for how tight screws must be are very vague on all guides.
a little time consuming to get it to work, but a fun process. so it was definitely not "working out of the box" as some say.
everything else is perfect and loving the process.
small tip, everyone keeps saying that the model doesn't stick to the base. through your slicing program either add the base that will support it, adds around an extra gram of printing, but even better I found that setting the slice program to make the first layer at +5 degrees to work perfect. the print sticks and doesn't move even when finished, you need to let it cool down. its that good. so for pla you put layer 1 at 65 degrees, and I printed a 2cm x 3cm object at height 25cm with no issue at all. I use this for all current tests and everything sticks properly and doesn't move.
I do NOT recommend using glue. i believe it will eventually compromise the quality. And since there is a better solution, adding things like glue is just pointless.
so far so good, aside from that part issue that is bent. everything else is great.
fii primul care lasă un comentariu